Brehs how much would it cost for a tune up on a 91 Sentra??

[Fatboi1]

I'm driving my 1st car again since my last two cars were totaled and this car feels like it needs a tune up.

How much you think a shop can do it for?? If not I can just pay someone to do it for me and get the parts myself although I don't know what to pay.

 

[Heafcliffe]

Fiancee had a 92 Sentra. Tune up was about $200 if I remember correctly. Included spark plugs, oil change, main belt removal/repair and an diagnostic check.

 

[SumBlackguyz]

might want to get that timing belt done too. if that goes, so does your car

 

[beenz]

might want to get that timing belt done too. if that goes, so does your car

That's what I'm having done to my car next time since I just hot 100k miles. Why does it cost damn near a G to have the timing belt replaced?

 

[The Bilingual Gringo]

That's what I'm having done to my car next time since I just hot 100k miles. Why does it cost damn near a G to have the timing belt replaced?

Mostly labor, it's a small dollar item. Depending on the car, they'll have to remove a lot of stuff, getting to the cylinder head, etc.

 

[Brooklynzson]

Def. get that timing belt & water pump done. Do the oil, air filter etc. You gonna spend a couple $100.

Almost done doing my timing belt, water pump & headgasket on my Civic

 

[The Bilingual Gringo]

Def. get that timing belt & water pump done. Do the oil, air filter etc. You gonna spend a couple $100.

Almost done doing my timing belt, water pump & headgasket on my Civic

Picture makes me want to vomit.

I did timing chains on my Corrado SLC. VR6's are fukking nightmares to work on.

 

[Brooklynzson]

Picture makes me want to vomit.

I did timing chains on my Corrado SLC. VR6's are fukking nightmares to work on.

Yeah, them shyts aint no joke. This shyt was easy though, the only hard part was gettin that fukkin crank pulley bolt off I broke 2 ratchets & an extention, stood one a 3 foot breaker bar & that shyt still didn't budge. I had to get a 7 ft pole from Home Deopot for it to crack.

 

[SumBlackguyz]

Yeah, them shyts aint no joke. This shyt was easy though, the only hard part was gettin that fukkin crank pulley bolt off I broke 2 ratchets & an extention, stood one a 3 foot breaker bar & that shyt still didn't budge. I had to get a 7 ft pole from Home Deopot for it to crack.

what i hear works is you position the breaker bar on the bolt against the ground then crank the engine real quick. the car will break the bolt for you

either that or get you a 1/2 inch impact gun

 

[The Bilingual Gringo]

Yeah, them shyts aint no joke. This shyt was easy though, the only hard part was gettin that fukkin crank pulley bolt off I broke 2 ratchets & an extention, stood one a 3 foot breaker bar & that shyt still didn't budge. I had to get a 7 ft pole from Home Deopot for it to crack.

Great mental picture

Crank pulley's are why I decided to go to Sears and cop a compressor.

 

[Brooklynzson]

what i hear works is you position the breaker bar on the bolt against the ground then crank the engine real quick. the car will break the bolt for you

either that or get you a 1/2 inch impact gun

Yeah thats the old school island way to do it, but i had already taken the engine apart.

Great mental picture

Crank pulley's are why I decided to go to Sears and cop a compressor.

I have a compressor, i honestly didn't even think about usin it. I guess I like doin stuff the manual way.
Plus that bolt was like so i had to get that fukka out w/ own two hands

 

[SumBlackguyz]

Luckily on my car i was able to sneak around having to take the crank bolt out

 

[Fckumeen]

Having uncles who are mechanics and own a bodyshop